Troubleshooting Steps For Adding A Permanent Route In Windows Server 2008

You should read these troubleshooting tips when you receive an error about adding a permanent route in Windows Server 2008 on your PC. To add a static option to a Windows Server 2007 multihomed computer, use the Routing and Remote Access Utility, which is still in the Manage section, or use the smart MMC snap-in. Then, right-click Static Routes under IPv4 or IPv6 and select New Static Route for IP Networks (see Figure 5.2).

Applies to: Windows Server Windows Vista, 2003, Windows XP, Windows Server 2008, Windows Windows Server 7, 2003 R2, Windows Server 2008 R2, Windows Server 2200, Windows Server 2012, Windows 8

Announces modified entries in the national IP router table. Used the help of recommendations, without the route is displayed. See Examples.

for examples of how to use this command.

Syntax

route [/f] [/p] [] [ [mask ] [] [metric ]] [if ]]

Settings

adding a persistent route in windows server 2008

/f

How do you add a persistent route?

To make the route more thorough, just add the -p option to help you with the command. For example: route – order 192 add.168. 151.0 MASK 255.255.

Clears the routing table of all entries except host routes (routes with netmask 255.255.255.Le 255), loopback network (routes with destination 127.0.0.0 but hides the network). 255.0.0. or 0) trusted multicast route (routes with 224 exit from .0.0.0 and netmask for 1 240.0.0.0). it If matches any of the statements (e.g., add, modify, or delete), the table is dropped, usually before the coma is executed.ndy. Use

/p

With the make use command, the specified route will be added to the registry and used to initialize the IP routing room table when TCP/IP is started. By default, routes added are never saved if the TCP/IP protocol is running normally. When using the image command, the passage list is always displayed. This setting is ignored for all other commands. Persistent routes are stored in the registry under HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesTcpipParametersPersistentRoutes.Den

specifies a run command. The actual commands are listed below:

add: add a route.

Edit: Edit an existing route.

delete: You can create a route to delete. Print multiple

print: or routes. files All

The

specifies the destination networks for the route. The destination can be a round-trip IP address (with the host bits associated with the network address set to help you be 0), equal to the IP address for the host, or the correct route, 0.0.0. For 0 defineThe default route is .

mask

Indicates the location of the network’s route to. The destination can be an IP network coverage (with the host bits in the connection address set to 0), any type for a host ip address with a route, 0.0.0.0 for a regular route.

How do I add a static route in Windows?

route ADD mask destination subnet network mask gateway_IP metric cost.Route mix 172.16.121.0 Mask 255.255.255.0 10.231.3.1.route -p provides the mask 172.16.121.0 255.255.255.0 10.231.3.1.route exclude target_network.Remove route 172.16.121.0.

How do I add a persistent route to Windows Server?

C:> PRINT ROUTE. Add for inactive route,C:> route -p ADD 10.10.10.0 MASK 255.255.255.0 192.168.1.1 METRIC 1.HKEY_LOCAL_MACHINESYSTEMCURRENTCONTROLSETSERVICESTCPIPPARAMETERPERSISTENTROUTES.C:> ROUTE.

Specifies the forwarding ip address or next hop, accessible via the addresses specified by the network station, and the subnet mask. For local subnet routes, the connected terminal address is the IP address corresponding to the connected interface to the subnet. For remote links accessible by one or more wireless routers, the gateway address is the IP address directly accessible by the neighboring router.

How do I add a static route?

Go to > Network Configuration > > IP Routes. Click Add, enter to have a static route to the station’s network or host. Enter the ip address of interest and the network cache ip address (255.255.255.255 for host), routing, and the next hop IP address.

Metric A

indicates a very good integer cost range (from metric 7 to 9999) for a route, often used when choosing between multiple routes in a routing table, which in turn best match the destination of the packet to be transmitted. with Route actual metric for Topped the bottom plus. The metric can reflect the number of hop rates, paths, path reliability, throughput options, or administrative properties.

if

Specifies the working index for an interface that the target is normally reachable to. For a complete list of interfaces and their optional interface indexes, use display with the route print command. you can use index values ​​in decimal or hexadecimal interface. For hexadecimal values, prefix the number 0x to the hexadecimal value. If the parameter is omitted, the base interface is determined by the gateway address.

/?

Show help on this request.

  • The large values ​​in the full column of the routing table are the result of TCP/IP authorization, which automatically calculates metrics for the schemes in the routing table based on the IP address, subnet, and default gateway configuration for each interface that defines a unique LAN. Automatic detection of all interface metrics, which includesBy default, it determines the speed of each interface, but adjusts the route metrics to get each interface as fast as possible, it is possible for the interface to create routes with the lowest metric. To suppress core metrics, disable the detection of auto-linked interface metrics in each of our TCP/IP protocol properties for each LAN connection.

  • adding a persistent route in windows server 2008

    Names can be used as a target if the corresponding available entry is stored in a LAN directive in the **systemrootSystem32Drivers**Etc folder. Names are eligible for payment if they can be resolved to IP addresses using standard host name resolution methods such as the Domain Name System (DNS) using the local host registry stored in **systemrootsystem32drivers** etc for NetBIOS name resolution.

  • If the normal or print delete command is used, the gateway parameter can be omitted and wildcards can be used for the destination as well as the la gateway. The target value can be a general designated value, a single asterisk (*). If the destinationwith the name a containing an asterisk (*) or a key question mark (?), it will be treated as a placeholder and will only match destination routes or print. An asterisk matches any string of characters, and a question mark also matches a single character. For example, 10.*.1, 192.168.*, 127.* and *224* are valid uses for the asterisk wildcard.

    Hinzufugen Einer Dauerhaften Route In Windows Server 2008
    Agregar Una Ruta Persistente En Windows Server 2008
    Aggiunta Di Un Percorso Persistente In Windows Server 2008
    Dodanie Stalej Trasy W Systemie Windows Server 2008
    Ajout D Une Route Persistante Dans Windows Server 2008
    Windows Server 2008에서 영구 경로 추가
    Dobavlenie Postoyannogo Marshruta V Windows Server 2008
    Adicionando Uma Rota Persistente No Windows Server 2008
    Een Persistente Route Toevoegen In Windows Server 2008